Difference between revisions of "Printer Command Set"
|Line 41:||Line 41:|
=== incrementPosition ===
=== incrementPosition ===
<blockquote>Command: '', ''dx'': int16, ''dy'': int16
Revision as of 00:37, 31 December 2013
- 1 Overview
- 2 Command Set Functions
- 2.1 Position and movement
- 2.2 Cartridge
- 2.3 Configuration
- 2.4 Peripherals
- 2.5 Other
Rapid prototyping hardware such as 3D printers and CNC routers often interpret G-code instructions. G-code is well suited to multi-tool vector based plotting, which printing a circuit is not. A communication protocol has been specifically designed for the Argentum which should be easy for the hobbyist community to experiment with.
Each command has a byte-code identifier and zero or more parameters that include unsigned and signed 8, 16, and 32 bit integers; null terminated arrays; and arrays of a length defined by a preceding integer parameter. The command name, e.g. getPosition, is used in the AgInterface Python controller and the command handler functions in the firmware. When extending the command set or implementing a serial controller or file writer, keep in mind the following:
- The commands are byte-packed (for computers to read). As in, the numbers are signed or unsigned integers of a particular byte-size. In contrast, G-code uses string representations of numbers (for humans to read). Unfortunately, this means it is not easy to write commands manually.
- Ideally, commands that "set" information or make the printer perform a function have uppercase ASCII byte-code identifiers, and commands that "get" information have lowercase. This is not a requirement, and eventually the human readable ASCII characters may run out.
- The AVR microcontroller is little-endian, so be careful if you're using some exotic controller hardware.
The Argentum Printer can read commands from the serial interface or files on an SD card. When reading from a file, the responses are ignored. See Printer Command Set Table for a table of command byte-code mappings.
Command Set Functions
Position and movement
Response: xpos: int16, ypos: int16
Get the current head position in steps, relative to the zero-point.
Command: 'P', xpos: int16, ypos: int16
Move the head to step position (xpos, ypos), relative to the zero-point.
Zero the head position Makes the current position be location (0, 0).
Command: 'I', dx: int16, dy: int16
Move the head by dx steps horizontally and dy steps vertically.
Command: 'T', cartridge: uint8, count: uint8
Fire all of cartridge's nozzles by iterating over address signals count times. The cartridge number uses bit places to address multiple cartridges, e.g. a value of 0b01 corresponds to the first cartridge, 0b10 corresponds to the second cartridge, and 0b11 corresponds to both the first and second cartridges.
Command: 'F', cartridge: uint8, nozzle: uint8, count: uint8
Fire the nozzle number of cartridge number cartridge a total of count times.
Command: 'R', cartridge: uint8, stepsPerDot: uint8, numDots: uint16, data: uint8
Burst mode firing. Print numDots dots with stepsPerDot X-axis steps between them. The total distance travelled will be stepsPerDot × numDots steps. The firing information is in the data array, which is of length num-set-bits(cartridge) × numDots × 13 bytes. Each byte represents primitive signal values. The format is ordered first by dot position, then by cartridge number as it appears from least-significant bit to most significant, and then by address from 1 to 13.
For example, for cartridge 0b11 and stepsPerDot of 100, the bytes would be ordered: [ dot0-cartridge1-address1, dot0-cartridge1-address2, ..., dot0-cartridge1-address13, dot0-cartridge2-address0, dot0-cartridge2-address0, ..., dot99-cartridge2-address13 ]
Command: 'c', field: uint16
Response: value: uint32
Get the calibration value of field. The field may be:
- HEAD_SPEED_X (0x01) for the time between X-axis motor steps, in microseconds.
- HEAD_SPEED_Y (0x02) for the time between Y-axis motor steps, in microseconds.
Command: 'C', field: uint16, value: int32
Set the calibration of field to value. See getCalibration for the list of valid fields and their corresponding byte codes.
Response: majorRevision: uint16, minorRevision: uint16
Get the firmware version number.
Command: 'd', pinNumber: uint8
Response: value: uint8
Read the digital value of pinNumber pin (Arduino numbering). Automatically sets required registers to allow input. Response value is 0x00 for false, and 0x01 for true.
Command: 'D', pinNumber: uint8, value: uint8
Write the digital value of pinNumber pin (Arduino numbering). Automatically sets required registers to allow output. The value argument is 0x00 for false, or else true. The firmware will not be responsible for making sure the pin isn't already used for motor or cartridge control.
Command: 'a', pinNumber: uint8
Response: value: uint16
Read the analogue (ADC) value of pinNumber pin (Arduino numbering). Automatically sets required registers to allow input. Response value is the ADC reading. The firmware will not be responsible for making sure the pin isn't already used for motor or cartridge control, or for checking that the pin is ADC capabable.
Command: 'A', pinNumber: uint8, dutyCycle: uint8
Write the analogue (PWM) value of pinNumber pin (Arduino numbering). Automatically sets required registers to allow output. The dutyCycle argument can be between 0x00 (0% duty cycle) and 0xFF (100% duty cycle). The firmware will not be responsible for making sure the pin isn't already used for motor or cartridge control, or for checking that the pin is PWM capabable.
Command: 'W', milliseconds: uint32
Pause reading commands for milliseconds number of milliseconds.
Command: 'B', filename: uint8, 0x00, mode: uint8, dataLength: uint32, data: uint8[dataLength]
Response: status: uint8
Perform an action on a file named filename, a null-terminated string, on the SD card. This can be used to write commands to the SD card and then execute it.
The parameter mode must be one of:
- FILE_WRITE (0x01) to write to a file, overwriting any previous data if it exists.
- FILE_APPEND (0x02) to append to a file, requiring that the file already exists.
- FILE_EXECUTE (0x03) to execute the commands contained in a file.
For FILE_WRITE and FILE_APPEND commands, the dataLength must be the byte length of the data buffer to be transferred. If filename is FILE_SERIAL (0xFF), both write and append commands will output to the serial interface.
For FILE_EXECUTE commands, a filename must be given, and the dataLength parameter must be 0x00 and no data be sent.
The response status is:
- EXECUTE_SUCCESS (0x00) on successful completion.
- NO_SD_CARD (0x01) if there is no SD card present.
- NO_FILE_EXISTS (0x02) if the mode is set to FILE_EXECUTE or FILE_APPEND and the file corresponding to filename does not exist.
- UNKNOWN_CMD (0x03) if an unknown command is encountered while executing the file.
- UNKNOWN_PARAM (0x04) if an unknown mode parameter is given or the mode is FILE_EXECUTE and the dataLength parameter is not 0x00.
Command: 'G', cmd: uint8, 0x00
Execute a null terminated G-code command.
Command: 0xFF, cmd: uint8
Execute a command in the secondary command set.